AVR325 harman/kardon
FRONT-PANEL CONTROLS
press this button to select Dolby modes, and thento switch between Stereo and Mono modes for FMÅ¡ Volume Control: Turn this knob clockwise to
press the Surround Mode Selector 8 to chooseradio reception. When weak reception is encountered,increase the volume, counterclockwise to decrease the
from the various mode options.press the button until the Stereo Indicator H goesvolume. If the AVR 325 is muted, adjusting volume
out to switch to Mono reception. Press and hold againcontrol will automatically release the unit from the
8 Surround Mode Selector: Press this button
to select from among the available surround modeto switch back to Stereo mode. (See page 30 for moresilenced condition.
options for the major mode group selected. The information on using the tuner.)A Input Indicators: A green LED will light to the left
specific modes will vary based on the number of& Optical 3 Digital Input: Connect the optical digitalof the input that is currently the input source for the
speakers available, the major mode group andoutput of an audio or video product to this jack.AVR 325.
whether the input source is digital or analog. For
example, press the Surround Mode Group Selector* Coaxial 3 Digital Input: Connect the coaxial dig-� Main Information Display: This display delivers
7 to select a major mode grouping such as Dolby orital input of a digital audio product such as a portablemessages and status indications to help you operate
Logic 7, and then press this button to see the specificaudio player or video game to this jack.the receiver. (See page 7 for a complete explanation
of the Information Display.)
mode choices that are available. For more information( Video 4 Video Input Jacks: These jacks may be
on mode selection, see page 26.used to connect the video play/out jacks of a video? Remote Sensor Window: The sensor behind
game or portable video product such as a camcorder,this window receives infrared signals from the remote
9 Tuning Selector: Press the left side of the buttonvideo game or digital still camera to your system.control. Aim the remote at this area and do not block
to tune lower-frequency stations and the right side of
the button to tune higher-frequency stations. When a� Video 4 Audio Input Jacks: These audio/videoor cover it unless an external remote sensor is
station with a strong signal is reached, the TUNEDjacks may be used for connection to the audio play/outinstalled.
Indicator I will be lit in the Main Informationjacks of a video game or portable audio/video productO Surround Mode Indicators: These LEDS will
Display �.such as a camcorder or portable audio player.light to show the surround mode and digital bitstream
) Button: When making system configuration� Bass Control: Use this control to boost or reducein use. Note that depending on the specific combina-
changes using the front-panel controls, press this but-the low-frequency output of the left/right front chan-tion of input sources and surround mode selected,
more than one indicator may light. (See page 28 for
ton to scroll left through the available choices for thenels by as much as ?10dB. Set this control as youmore information.)
option being adjusted.find suitable to adjust to your specific taste or room
acoustics.
! Tuner Band Selector: Pressing this button will
automatically switch the AVR 325 to the Tuner mode.y Balance Control: Use this control to change the
Pressing it again will switch between the AM and FMrelative volume for the front left/right channels.
frequency bands. (See page 30 for more information
on the tuner.)NOTE: When multichannel surround modes are in use,
this control should be at the midpoint, or O12 oOclock,�
@ Set Button: When making system configurationposition for proper operation.
changes using the front-panel controls, press this but-
ton to enter a setting into the unitOs memory.O Treble Control: Use this control to boost or
reduce the high-frequency output of the left/right front
#? Button: When making system configurationchannels by as much as ?10dB. Set this control as
changes using the front-panel controls, press this but-you find suitable to adjust to your specific taste or
ton to scroll right through the available choices for theroom acoustics.
option being adjusted.� Channel Adjust Selector: Press the button to
$ Preset Station Selector: Press this button tobegin the process of adjusting the channel level out-
scroll up or down through the list of stations that haveputs using the source currently playing through your
been entered into the preset memory. (See pages 30AVR. For complete information on adjusting the chan-
and 31 for more information on tuner programming.)nel output level, see page 31.
% Input Source Selector: Press this button toU Delay Adjust Selector: Press this button to
change the input by scrolling up or down through thebegin the process of adjusting the delay settings for
list of input sources.Dolby surround modes. See page 23 for more infor-
mation on delay adjustments.
^ Tuner Mode Selector: Press this button to select
Auto or Manual tuning. When the button is pressed soU Digital Input Selector: Press this button to begin
that the AUTO Indicator J lights, the tuner will searchthe process of selecting a digital source for use with
for the next station with an acceptable signal when thethe currently selected input. Once the button has been
Tuning Selector 9ué is pressed. When thepressed, use the ? or ? Buttons )# to choose
button is pressed so that the AUTO Indicator J is notthe desired input and then press the Set Button @
lit, each press of the Tuning Selector 9ué willto enter the setting into the unitOs memory. See page
increase the frequency. (See page 30 for more informa-27 for more information on digital audio.
tion on using the tuner.) This button may also be used
6
6 |